Alarms & Sirens

The new Singlewire InformaCast IP66 Outdoor Horn provides an easy method for implementing a loud IP-based overhead paging system for loud areas, warehouses, manufacturing areas, and outdoor areas. Now with up to 9 user-stored messages. The interface is compatible with most SIP-based IP PBX servers that comply with the SIP RFC 3261. For non-SIP environments, the speaker can be configured to listen to multicast address and port number combinations to form paging zones.

When installed, the wall-mounted Singlewire RGB Strobe operates as a visual alerting device.In Singlewire mode, when an audio page is sent to the strobe, a specific color, brightness and blink rate can be selected based on the priority of the page. The Singlewire RGB Strobe supports 10 Singlewire priority levels.

In the SIP mode, the device can be set up as part of a ring group (call group) with the Strobe's specific scene engaged as notification of incoming calls. Through a web page setup, you can have the Strobe respond to message waiting signals by blinking. When the message has been heard, the strobe stops blinking.

The Singlewire RGB Strobe may also be activated by being part of a Multicast group. When audio is detected on a specific Multicast address and port, the strobe will activate.

Users may also use CyberData's HTTP command set to directly access the strobe's functions.

When installed, the wall-mounted SIP RGB Strobe operates as a visual alerting device. The device can be set up as part of a ring group (call group) with the Strobe engaged as notification of incoming calls. The SIP RGB Strobe may also be activated by being part of a Multicast group. When audio is detected on a specific Multicast address and port, the strobe will activate.

Through a web page setup, you can have the SIP Strobe respond to message waiting signals by blinking. When the message has been heard, the strobe stops blinking.

Multiple colors, Blink rate and brightness can be selected for each of the different activation methods Users may also use CyberData's HTTP command set to directly access the strobe's functions.

Note: Support of SIP RGB Strobe with Syn-Apps devices via multicast mode.

The Auxiliary RGB Strobe Kit comes with a 1-meter cable that enables the user to connect to a supported CyberData IP endpoint.

Power and signaling for the strobe comes from the attached CyberData Endpoint.

Setup of the strobe's blink rates and brightness are through the web interface of the attached CyberData IP endpoint.

The Crestron® TSW-1070-LB is a room availability light bar designed for use withTSW-1070orTSS-1070series touch screens. The TSW-1070-LB provides a 180° visual indication of a room's availability as part of a complete enterprise room scheduling solution. The TSW-1070-LB mounts easily to the rear of the touch screen and illuminates bright green or red to indicate the room availability status, with options for custom color mixing and programming. The TSW-1070-LB features a clean, stylish appearance and vivid color illumination that complement any corporate office environment, and it is energy efficient at less than 2 W power consumption.

Room Availability Status

For room scheduling applications, the TSW-1070-LB simply connects to the touch screen via USB and requires no special programming or configuration.1 The illumination color is controlled by the room scheduling application, which runs on the touch screen and syncs with the Crestron Fusion® software or another room scheduling application. The TSW-1070-LB illuminates green when the room is available and red when the room is occupied. It can also blink to indicate an emergency message broadcast from Crestron Fusion.

Custom RGB Color Mixing

For custom applications, the TSW-1070-LB can be configured to illuminate in almost any desired color. The TSW-1070-LB features tricolor RGB LEDs that allow for a full spectrum of colors by blending the red, green, and blue elements in 1% increments. Custom RGB color mixing is performed either through the touch screen directly or via custom control system programming. A Crestron control system connected to the touch screen can be programmed to support various functionality, enabling colors to alternate, fade in and out, or blink on and off as desired.

Versatile Mounting Options

The TSW-1070-LB is compatible with various TSW-70 series mounting solutions to support installations common for room scheduling touch screens, including the TSW-70-UMB universal mounting bracket, the TSW-1070-MSMK multisurface mount kit, and the TSW-770/1070-MUMK mullion mount kit.

Key Features

• Provides a 180° visual indication of a meeting room's availability for TSW-1070 or TSS-1070 series touch screens
• Features a stylish appearance designed to complement corporate office environments
• Illuminates vivid green or red to clearly indicate room status
• Supports RGB color mixing to allow for almost any color illumination
• Energy efficient at less than 2 W power consumption
• Mounts easily to the rear of the touch screen
• Single-wire USB connectivity
• Compatible with various in-wall, multisurface, and mullion mounting accessories
• Available in smooth black or white finish