Rack & Cabling
-
Eaton Tripp Lite Series HDMI Send/Receive Pass-Through Wallplate, White (F/F) - 2 x Socket(s) - HDMI Video - White
With Tripp Lite's HDMI Send/Receive Pass-Through Wallplate, you can now hide that HDMI cable that's connected to the Flat Screen HDTV hanging on the wall, by running the cable behind the wall and into the back of the faceplate. Then connect a cable from your DVR or SAT box into the front of the faceplate - no unsightly cable dangling down from your TV. If your DVR or SAT box is located a long distance from the HDTV, use Tripp Lite's P166-001-A, Active wallplate with signal booster.
Learn MoreRegular Price: $11.77
Special Price $11.06
-
Eaton Tripp Lite Series HDMI over Dual Cat5/Cat6 Extender Wall Plate Kit with Transmitter and Receiver, TAA - Wall Mount
With Tripp Lites HDMI Over Cat5/Cat6 Wallplate Extender Kit, you can locate a HDMI enabled display up to 230 ft. away from the HDMI source, using readily available Cat5 or Cat6 UTP cable (for best performance, use Solid wire Cat6). The kit consists of a Passive wallplate at the source side, and an Active wallplate (with built-in signal regenerator) at the display side. Simply run two Cat5/6 UTP cables between the two wallplates, and plug in standard Tripp Lite HDMI patch cables to the HDMI source and the display. The Green LED on the Display wallplate lets you know that power and a signal are coming from a connected source. The Red LED indicates only a signal is being received. The kit is functioning properly when the unit is connected to a display and the Green LED is lit.
Learn MoreRegular Price: $98.55
Special Price $92.64
-
Eaton Tripp Lite Series Hook-and-Loop Cable Ties, 10" L x 5/8" W - 10-Pack - Cable Tie - Black - 10 - 10? Length
Tripp Lite's Hook-and-Loop Velcro Cable Tie 10 Pack is the must have accessory for keeping bundles of cables manageable. Will not crimp Cat5/Cat6 patch cables like nylon ties when over-tightened, and, unlike nylon ties, are re-usable over and over again. 10" Long by 5/8" Wide x 10 pieces.
Learn MoreRegular Price: $4.77
Special Price $4.48
-
Eaton Tripp Lite Series 7.5" Nylon Cable Ties - 100-Pack - 40lb Strength
Tripp Lite's 100 Pack of Nylon Cable Ties is the must have accessory for keeping bundles of cables manageable. At 7.5" Long, just zip up the cable tie and clip off the remainder for a clean, organized installation. Provides a minimum tensile strength of 40 lbs. (18 kg.).
Learn MoreRegular Price: $5.17
Special Price $4.86
-
Eaton Tripp Lite Series HDMI Cable Lock - Clamp/Tie/Screw - Cable Lock - Black - Nylon
HDMI Port Lock Helps Prevent Accidental Disconnection and Expensive Downtime
Having a cable come loose accidentally can mean the loss of an audio/video signal and costly downtime. The P568-000-LOCK helps you avoid interruptions in your digital signage system by maintaining a secure link without failure. A locking HDMI connection is also invaluable when moving equipment in a rack or removing equipment from tight areas, ensuring the cable always stays connected.
Easy to Install in Just a Few Minutes
This HDMI lock works with any HDMI cable and any device with a fixing or locking screw space above or below the HDMI port. If the device has no screw in the fixing space, one is included. Just secure the included nylon cable tie to the fixing space with the screw, and insert your HDMI cable into the cable tie clamp, pushing the clamp as close to the connector as possible. Then, plug the cable into the device's HDMI port, and insert the cable tie into the clamp, removing all slack, so the HDMI plug cannot come loose. Removing the cable tie from the clamp allows you to unplug the cable.
Lifetime Warranty
The P568-000-LOCK is backed by a lifetime warranty, ensuring reliability and performance.
Learn MoreRegular Price: $2.49
Special Price $2.34
-
Eaton Tripp Lite Series SmartRack 12U Standard-Depth 4-Post Open Frame Rack - 19? 12U Wide x 36? Deep for Patch Panel, A/V Equipment, Server - Black Powder Coat - Steel - 1000 lb x Maximum Weight Capacity - 1000 lb x Static/Stationary Weight Capacity
The SmartRack 12U Standard-Depth 4-Post Open Frame Rack provides an economical rack-mount solution for small offices, retail locations and other secure IT locations with limited floor space where you need equipment to be organized and easy to access. It's ideal for mounting network switches, routers, patch panels, audio/video components and other EIA-standard 19-inch rack equipment up to 36 inches deep.Constructed from heavy-duty steel with a durable black powder-coated finish, the SR12UBEXPNDKD has a maximum load capacity of 1,000 pounds. Stashed away under a counter, on a workbench or in a corner, this rack saves precious space and allows you fast, easy access at your immediate workspace for organizing, installing and servicing equipment and cabling. The open design allows unobstructed airflow to help keep components cool and performing at their peak.The self-squaring SR12UBEXPNDKD assembles using the included hardware. Built-in casters allow you to roll the rack into place. The vertical mounting rails have square, numbered holes and optional cable management hooks for securing equipment to the steel frame. Only user-supplied standard hand tools are required for setup. Toolless button holes accept 0U vertical installation of PDUs and cable managers.
Learn MoreRegular Price: $296.99
Special Price $279.17
