Hardware Connectivity

The DICENTIS System Cable Assemblies are terminated at both ends with RJ45 like connectors with additional power pins. The cable assemblies are used to connect a DICENTIS device to the audio powering switch or to the powering switch. It provides network communication and power transports in one cable. The cable assemblies are used when loop-through and redundant cable connections are required. The cable assemblies have a low smoke zero halogen jacket to comply with safety and environmental standards. The cables are solid core which provides better performance for cable lengths over 5 meter.

Learn More

Telex Coaxial Antenna Cable - 25 ft Coaxial Antenna Cable for Antenna, Intercom - First End: RP-TNC Antenna Learn More

The DICENTIS cable coupler enables Technicians to connect DICENTIS cable assemblies (with one another or with standard CAT-E cable) without the need for special tools.

The cable coupler can be used to:

• Connect two DICENTIS cables so you can easily increase cable length.
• Connect two DICENTIS cables, where one is always present and ends in a "floor pod" and the other cable is only connected when it is required (for example, a rostrum microphone which will not always be used). The cable coupler can be fixed with screws to the floor pod.
• Interconnect DICENTIS cable with standard CAT5-E cable and power cable so you can comply with local regulations or make use of current available infrastructure
• Interconnect DICENTIS cable with standard CAT5-E cable and a 48VDC power supply close to the devices
• Create a circuit to power on a system without the need of a Multimedia device, a PC running the Meeting application, or Synoptic control.

Functions

• Makes it is easier to adjust cables to the required length when installing rental systems. Offers a means to create cables for the desired length by just interconnecting standard cables without the need for special tools.
• Makes it easy to connect "temporary" devices (for example, a rostrum microphone) to the DICENTIS system. At the location of the rostrum microphone, the cable coupler is used as the endpoint of the cable (mounted in a floor pod).
• Makes it possible to comply to the most stringent norms for fixed/installation cable in buildings. Enables you to use standard CAT-5E and power cable for the part where the norms have to be met, and DICENTIS cable in the conference room.
• Makes it easy to re-use existing infrastructure/ networks (for example, if a CAT-5E network is already in place).
• Makes it possible to place a 48 VDC power supply (not part of the Bosch portfolio) close to the participant devices.

Requirements for the power supply:

• nominal output of 48 VDC (ranging from 47 - 49 VDC).
• the ripple should be less than 200 mV pk-pk.
• maximum output current should not exceed 3.0 A (or limited to 3.0 A, because DICENTIS cables and devices have a maximum rating for this current).

Advice

• It is strongly advised that the power supply has its own short circuit protection with a short circuit output current ranging from 4.3 to 5.0 A.
• When the power supply has an automatic restart after a short circuit, this restart function should have an interval time of 3 to 4 seconds and should have no more than 4 restart attempts.
• Upon powering off the power supply, the output should be less than 9 V, 1 mA.

Learn More

3 m (9 ft) analog cable, SMB (female) to BNC (male) to connect camera to monitor or DVR.

Learn More

Cable terminated at both ends with a molded six-pole circular connector (male and female). The extension to the type number gives the length of the cable.

Learn More

Bosch VPUSB Video Cable Adapter - Coaxial Video Cable - First End: BNC Video - Second End: USB - 1 Learn More

Cable terminated at both ends with a molded six-pole circular connector (male and female). The extension to the type number gives the length of the cable.

Learn More

RTS 25' Super-Flex Dual-Channel Cable with XLR-6 M/F Connectors - 25 ft XLR Audio Cable for Audio Device, Intercom - First End: 1 x 6-pin XLR Audio - Male - Second End: 1 x 6-pin XLR Audio - Female - Shielding Learn More

• Premium ultra-low-loss coax cable
• 50 ohm
• Robust male BNC connectors

The CXU100 is an ultra-low loss, premium-grade, 100 foot coax cable for UHF wireless microphone systems.

Its high-efficiency and low-attenuation characteristics make it ideal for system installations requiring lengthy cable runs between antennas and receivers.

Learn More