Power Injectors/Splitters

TRENDnet's Gigabit PoE Injector, model TPE-113GI, combines electrical power with a Gigabit network connection. Auto-sensing technology conveniently delivers the correct wattage needed to power your PoE devices. Connect the injector to a non-PoE Gigabit switch and then run an Ethernet cable with data + power to network a PoE device up to 100 meters (328 ft.) away.

• Full Duplex Gigabit speeds
• Supplies PoE (15.4W)
• Network a PoE device located up to 100 meters (328 ft.) away
• Converts a non-PoE Gigabit port to a PoE Gigabit port
• Save on installation and equipment costs
• IEEE 802.3af compliant
• NDAA compliant

More from the Manufacturer

OmniConverter GXPoE+/S and GXHPoE/S are unmanaged gigabit PoE Extenders that enable the delivery of Ethernet data and Power over Ethernet (PoE) beyond the standard 100 meter limit of twisted pair copper cabling.

OmniConverter PoE Extenders provide cost-effective distance extension and connectivity to remote PoE devices where external power is not available or hard to provision, or when replacing copper with fiber becomes cost prohibitive.

OmniConverter PoE Extenders are 10/100/1000BASE-T Ethernet extenders that function as both Powered Devices (PD) and Power Sourcing Equipment (PSE), and require no external AC power. They feature one PoE/PD port and one or two PoE/PSE ports, and can be powered by an IEEE 802.3at or High-Power PoE 60W power source, such as an OmniConverter GHPoE/Sx or GHPoE/M HPoE PSE switch.

Utilizing data regeneration and voltage level boosting capabilities, OmniConverter PoE Extenders can be daisy chained to break through the Ethernet copper distance barrier and deliver 10/100/1000 data and power to multiple PoE powered devices.

Due to cable resistance, voltage drop across the cabling could lower the voltage below the minimum standard requirement of the attached PD. OmniConverter PoE Extenders have smart voltage-boosting technology to maintain the required standard compliant PoE voltage levels between hops.

The PoE Extenders automatically negotiate and deliver the power level required by a Powered Device (PD) partner. When a non-PoE device, such as a laptop, is connected to the PoE Extenders for data only applications, no power is applied.

OmniConverter PoE Extenders are plug-and-play devices that support auto-negotiation of data rates and duplex modes for simple in-line installation to instantly extend network distances. The PoE Extenders are fully operational once a PSE source is applied to the PoE/PD port, displaying power and operational status without a PD attached. This facilitates the installation and troubleshooting by ensuring each link is operational.

The OmniConverter PoE Extenders can be wall mounted or DIN-rail mounted using the optional DIN-rail mounting clip.

INJ 2100-T PoE Injectors are DIN Rail mounted single port, PoE mid-span injectors. In environments vulnerable to voltage surges, it acts as an intermediary devices between a non-PoE switch and a PoE device to inject fully compliant power over the Ethernet cable. With electrical isolation of the internal power supply, the INJ-2100-T units are protected against short circuits on the PoE side. The integrated surge protection increases system availability by protecting the connected end devices.

Generating up to 60 Watts, the INJ-2100-T provides electrical power to remote PD access points, pan-tilt and zoom (PTZ) cameras and video-phones. It complies with the IEEE802.3bt Hi-PoE (60W of power) or IEEE 802.3at PoE+ (30W of power) standards and is also backward compatible with IEEE802.3af PoE (15.4W of power).Learn more about PoE.

With the INJ-2100-T, there is no need to buy an expensive PoE switch or install electrical wiring and outlets in hard to reach locations. Just use and open port on an existing non-PoE switch to save time and money by sending power and data over the same cable.

INJ 2100-T PoE Injectors are DIN Rail mounted single port, PoE mid-span injectors. In environments vulnerable to voltage surges, it acts as an intermediary devices between a non-PoE switch and a PoE device to inject fully compliant power over the Ethernet cable. With electrical isolation of the internal power supply, the INJ-2100-T units are protected against short circuits on the PoE side. The integrated surge protection increases system availability by protecting the connected end devices.

Generating up to 60 Watts, the INJ-2100-T provides electrical power to remote PD access points, pan-tilt and zoom (PTZ) cameras and video-phones. It complies with the IEEE802.3bt Hi-PoE (60W of power) or IEEE 802.3at PoE+ (30W of power) standards and is also backward compatible with IEEE802.3af PoE (15.4W of power).Learn more about PoE.

With the INJ-2100-T, there is no need to buy an expensive PoE switch or install electrical wiring and outlets in hard to reach locations. Just use and open port on an existing non-PoE switch to save time and money by sending power and data over the same cable.