Power Injectors/Splitters

TRENDnet's Gigabit PoE Splitter, model TPE-104GS, networks a non-PoE device in a remote location using a PoE network connection. The TPE-104GS splits a Gigabit PoE connection into separate power and Gigabit data sources. A convenient dip-switch adjusts output power to 5V, 9V, or 12V in order to match non-PoE device power requirements. The included combination 2.0 and 2.5mm jumper cable provides greater device compatibility.

• GIGABIT ETHERNET DEVICE INTERFACE: 1 x Gigabit data/power port in; 1 x Gigabit data out port; 1 x DC Power out port; LED indicators; Adjustable output power DIP switch (5V, 9V, 12V)
• NDAA COMPLIANT: With our NDAA compliant Splitter, you can plan and install networking solutions that Government customers demand today (U.S. and Canada Only)
• MANUFACTURER PROTECTION: We stand by the quality of our products.The TPE-104GS Gigabit PoE Splitter is backed and supported with 3 years of TRENDnet Manufacturer Protection.
• POE POWER: No power adapter necessary; the Gigabit PoE Splitter takes a PoE network connection, and splits power and data into separate connections to network a non-PoE device with power up to 100m (328 ft.).
• ADJUSTABLE VOLTAGE OUTPUT: Convenient dip-switch adjusts voltage output to 5V, 9V, or 12V in order to match non-PoE device power requirements. The included combination 2.0 and 2.5mm jumper cable provides greater device compatibility.
• WALL MOUNTABLE: Wall mountable design of the PoE Splitter accommodates most installation scenarios.
• DATA TRANSFER RATES: Ethernet: 10Mbps (half duplex), 20Mbps (full duplex); Fast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex); Gigabit: 2000Mbps (full duplex)

More from the Manufacturer

POE Splitters are used to take the power supplied from a POE power supply and split off the data and DC power into separate connectors. These splitters are mainly used for powering legacy devices which are not POE enabled but instead get their power from a DC connector. The POE Y Splitters are useful when two devices need remote power, one device being POE enabled to accept power thru the RJ45 and the other device requiring DC power thru a DC connector. The overall length of these devices is 10 inches. The RJ45 Jack is a high quality CAT5 rated jack for high speed data.

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 56VDC Power Over Ethernet voltage from a 24V or 48V battery system. They have an integrated POE injector to apply the 24VDC or 56VDC to the CAT5 Ethernet cable. Passive POE and 802.3at models are available. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source.
They accept data-in to a shielded RJ45 Jack and provide data-out and POE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have a power output of up to 35W. The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.
If the remote device does not support power over Ethernet, splitters (POE-SPLT) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER cable can be used.

The TP-DCDC-4856GD-VHP is a special very high power DC to DC converter / POE inserter designed and qualified for use with Axis Q60 Series outdoor PTZ security cameras.

The DCDC converter supplies 35W per POE channel. One POE channel is using pins 4,5,7,8 and the other POE channel utilizes pins 1,2,3,6. By splitting the power onto separate POE channels, the device can achieve 70W total supplied power to the end device. The TP-DCDC-4856GD-VHP has separate LED indicators for indicating which 802.3at channel is being used by the client. The RIGHT LED indicates POE Channel 1 and the LEFT LED indicates POE Channel 2.

The TP-DCDC-4856GD-VHP has been qualified by Axis to be used with their Q60 series of PTZ cameras. The unit can be used with any 802.3at device as it will supply 35W to any 802.3at POE channel detected. If two channels are detected on the client then 70W power will be supplied.

They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. They have various protections for surge, short circuit and overload. The input and output are isolated.