Network & Communication
-
NVT Phybridge 16-Channel DigitalEQ Active Receiver Distribution Amplifier Hub - 3280.84 ft Range - 4 x Network (RJ-45) - Twisted Pair - Category 5 - Rack-mountable, Wall Mountable, Desktop
Features:
- Adaptive DigitalEQTM fully automatic 4-band equalization provides adjustment-free equalization every time
- Compact rack-mountable 19" 1U high enclosure features 16 channels with 2 outputs per channel
- Full motion CCTV video at distances up to 3,000ft (1km) when used with any passive NVT transceiver or hub; 1 mile (1,6km) when used with the NV-653T active transmitter; 1,000ft (300m) with shielded twisted-pair when used with any passive NVT transceiver or hub
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Automatic compensation for reverse-polarity wiring
- At-a-glance per-channel diagnostics
- Compatible with qualified UTP cameras
- Includes sixteen 2ft (60cm) coax jumper cables, rack mount hardware and four NV-RJ45A adaptors
- Limited lifetime warranty
The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. this allows the use of shared or existing cable plant. Ground-lifting ensures no annoying "hum-bars" when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated. Learn More$3,000.43 -
NVT Phybridge 16-Channel Power Supply StubEQ Active Receiver Hub - 1500 ft Range - 4 x Network (RJ-45) - Twisted Pair - Category 5 - Rack-mountable, Wall Mountable, Desktop
Features:
- Provides Class 2 SELV 28 VAC with up to 1 Amp/channel while receiving video transmission and delivering P/T/Z telemetry, all over a single 4-pair Cat5 cable for each camera
- Built-in distribution amplifier with 2 video outputs per channel
- Full motion CCTV video at distances up to 1,500ft (460m) when used with any passive NVT transceiver
- Adaptive StubEQTM fully automatic 2-band equalization provides adjustment free equalization every time, no manual adjustments required
- Automatic-reset fault protection; transient protection
- Individually floating power outputs and differential video inputs ensure total ground-loop immunity
- Diagnostic LEDs show load/no load, miswires, overload conditions, and video status
- Limited lifetime warranty
$2,689.04 -
NVT Phybridge NV-215J-M Media Converter - 1 x Network (RJ-45) - 0.23 km - External
NV-215J-M Video Transceiver is a passive (non-amplified) device that allows the transmission of real-time monochrome or color video over Unshielded Twisted-Pair (UTP) telephone wire. Baseband (composite) signals of any type are supported.
Learn More
The passive NV-215J-M has a 9" mini-coax pigtail lead which allows in-camera enclosure mounting in most dome cameras and a RJ45 for connection to UTP wire. It is capable of delivering a fully equalized signal to the DVR when used with any Active NVT PhybridgeReceiver, yet is compatible with all of NVT Phybridge's passive products for applications under 750ft (225m). The NV-215J-M Video Transceiver also incorporates improved transient protection that eliminates the need for a ground screw.
The unparalleled interference rejection and low emissions of the NV-215J-M allow video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable plant. -
NVT Phybridge Power-Video Passive Transceiver - 3280.84 ft Range - 1 x Network (RJ-45) - Twisted Pair
NV-216A-PV Video Transceiver with Power is a passive (non-amplified) device that allows the transmission of real-time monochrome or color video over Unshielded Twisted-Pair (UTP) telephone wire. Baseband (composite) signals of any type are supported.
NV-216A-PV video transceiver allows transmission of CCTV video and low voltage power over UTP cable. The NV-216A-PV incorporates the transceiver engine of NVT's popular NV-214A-M video transceiver with the added value of camera power connections. Power and Video are routed via UTP and RJ45 connections. Used at the camera, the passive NV-216A-PV has a compact body, a male BNC for direct connection to the camera, and is compatible with NVT's PVD™ product line. Connect the RJ45 to 4-pair cable to be routed to the NVT Phybridge cable integrator and on to an active or passive receiver hub in the MDF/Control Room.
Learn More -
NVT Phybridge Single Channel Passive Video Transceiver - 39.37" Range - 1 x Network (RJ-45) - Twisted Pair
NV-217J-M Single Channel Passive Video Transceiver is a passive (non-amplified) device that allows the transmission of real-time monochrome or color video over Unshielded Twisted-Pair (UTP) data wire. Baseband (composite) signals of any type are supported.
The passive NV-217J-M features a RJ45 connection and Male BNC allowing connection directly to the camera or DVR. It is capable of delivering a fully equalized signal to the DVR when used with any Active NVT Phybridge Receiver, yet is compatible with all of NVT Phybridge's passive products for applications under 750ft (225m). The NV-217J-M Video Transceiver also incorporates improved transient protection that eliminates the need for a ground screw.
The unparalleled interference rejection and low emissions of the NV-217J-M allow video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable plant.
Learn More -
NVT Phybridge NV-218A-PVD Video Transceiver - 3280.84 ft Range - 1 x Network (RJ-45) - Twisted Pair - Category 5
Model NV-218A-PVD Video Transceiver with Power and Data is a passive (non-amplified) device that allows the transmission of real-time monochrome or color video over Unshielded Twisted-Pair (UTP) telephone wire. Baseband (composite) signals of any type are supported.
This product incorporates the transceiver engine of NVT Phybridge's popular NV-214A-M video transceiver with the added value of Power and Data connections to and from the camera. Power, Video and Data are routed via UTP and RJ45 or screwless terminal block inputs/outputs. Used at the camera, the passive NV-218A-PVD has a 9" mini-coax mini lead for direct video output connection from the camera. Along side this coax lead are two sets of screwless terminal blocks for quick pass through connections for your camera's Power and Data. On the "house" or output side of the product you have the option of using convenient screwless UTP connectors or the more efficient RJ45.
The unparalleled interference rejection and low emissions of the NV-218A-PVD allow video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable plant. The NV-218A-PVD carries a limited lifetime warranty and is UL and cUL listed.
Learn More