Accessories
-
ComNet RLFDX485S2/HV Signal Repeater - 98425.20 ft Maximum Operating Distance - Serial Port
The ComNet™ RLFDX series of serial data link/repeaters are substation-rated and industrially hardened form, fit, function and completely backwards-compatible replacements for the popular Garrettcom/Dymec 5845 & 5846 series of RS-422 and RS-485 serial data link/repeaters. They are designed for deployment in environments where high levels of electromagnetic noise and interference (EMI) and severe voltage transients and surges are routinely encountered, such as electrical utility substations and switchyards, heavy manufacturing facilities, trackside and roadside electronic equipment, and other difficult out-of-plant applications. Optical connectivity provides significantly extended transmission distances compared to copper media; high levels of electrical isolation; enhanced reliability and protection for peripheral IEDs, RTUs, and other equipment; and operational safety.
Learn More
The RLFDX series of serial data link/repeaters are easily field-configurable for point-to-point, point-to-multipoint/Local-Remote, loop, or bus topologies. They may be also used for electrical data protocol translation: an RLFDX232-series RS-232 modem and IED/RTU can communicate directly with an RLFDX485-series RS-422/RS-485 modem and IED/RTU.
The extremely versatile and simple-to-install RLFDX series is ideal for any mission-critical application where very high levels of reliability and network availability are of the utmost importance.$1,559.50 -
ComNet RMB-2 Mounting Adapter for Network Switch, Network Equipment
The ComNet series of RMB Rack Mount Bracket Adaptor Kits are ideal for mounting select ComNet VL managed Ethernet switches within any standard 19-inch equipment rack cabinet. Three different RMB-series adaptor kits are available:
- RMB-1 Single-Module Rack Mount Adaptor Kit, with mounting hardware. This kit is to be used when rack-mounting one (1) ComNet model CWFE8TX8MS Ethernet Managed Switch unit, or any other select ComNet ValueLine module having a width dimension of 9.85 inches (250 mm).
- RMB-2 Single-Module Rack Mount Adaptor Kit, with mounting hardware. This kit is to be used when rack-mounting one (1) ComNet model CWGE2FE8MSPOE Ethernet Managed Switch unit, or any other select ComNet ValueLine module having a width dimension of 8.6 inches (217 mm).
- RMB-3 Dual-Module Rack Mount Adaptor Kit, with mounting hardware. This kit is to be used when rack-mounting two (2) ComNet model CWGE2FE8MSPOE Ethernet Managed Switch units, or two of any other select ComNet ValueLine modules having a width dimension of 8.6 inches (217 mm) each.
-
ComNet RMB-3 Mounting Adapter for Network Switch, Network Equipment
The ComNet series of RMB Rack Mount Bracket Adaptor Kits are ideal for mounting select ComNet VL managed Ethernet switches within any standard 19-inch equipment rack cabinet. Three different RMB-series adaptor kits are available:
- RMB-1 Single-Module Rack Mount Adaptor Kit, with mounting hardware. This kit is to be used when rack-mounting one (1) ComNet model CWFE8TX8MS Ethernet Managed Switch unit, or any other select ComNet ValueLine module having a width dimension of 9.85 inches (250 mm).
- RMB-2 Single-Module Rack Mount Adaptor Kit, with mounting hardware. This kit is to be used when rack-mounting one (1) ComNet model CWGE2FE8MSPOE Ethernet Managed Switch unit, or any other select ComNet ValueLine module having a width dimension of 8.6 inches (217 mm).
- RMB-3 Dual-Module Rack Mount Adaptor Kit, with mounting hardware. This kit is to be used when rack-mounting two (2) ComNet model CWGE2FE8MSPOE Ethernet Managed Switch units, or two of any other select ComNet ValueLine modules having a width dimension of 8.6 inches (217 mm) each.
-
ComNet Network Reader Interface For VBB And VLB Access Control Platforms - Door
The ComNet VBB-NRI is a cost-effective solution that can extend the reach of your bright blue system. This IP-based reader interface is perfect for remote locations where wiring can be a challenge. The VBB-NRI connects to the VBB or VLB controller board via your network, allowing you to bring remotely located readers online with your bright blue access control system.
The VBB-NRI is compatible with most card readers (any device with a Wiegand output) and supports facility lockdown and degraded mode.
Features for VBB-NRI- 10/100 BASE-T compatible
- Connects one reader via Ethernet network to the VBB or VLB controller
- Compatible with proximity, smart card, biometrics, magnetic stripe, barcode and Wiegand read head technologies
- Two form C, single pole/double throw, mechanically latching 1A relays (pre-programmed for dedicated functionality)
- Four contact inputs for Door exit request, Door position switch, Push button override, and Auxiliary input
- Facility lockdown via credential or external pushbuttton
- Degraded mode
- Metal enclosure with hinged and dual screw door
- On board connection for tamper switch
- Tamper switch, lock & key option available
- Supports DHCP or Static IP addressing
- Compatible with proximity, magnetic stripe and smart card technologies
- Reduces wiring and labor costs
- VBB-NRIs and VBB-RIs can be combined on a bright blue or lite blue system
- Suitable for small to mid-sized organizations with remote locations and an available IP network
$459.26 -
ComNet VP Smart Card - Proximity Card - Off White - ABS
The ComNet VP Series Proximity Credentials are available in a variety of styles and formats to meet your access control requirements. Whether you are looking for robust, clamshell style cards that can withstand harsh environments, standard ISO style credit-card size credentials, or tags that attach to a key ring or other device for utmost convenience, these 125 kHz proximity credentials can be mixed and matched to meet your every need. VP Series credentials are compatible with VI-Series Readers as well as industry standard proximity readers, and are passive devices that do not require batteries or maintenance.
Learn More
