Power Injectors/Splitters
-
Cisco IW-PWRINJ-60RGDMG= PoE Injector - 120 V AC, 230 V AC Input - 670 mA Output - RJ-45 Input Port(s) - RJ-45 Output Port(s) - 60 W
The IW-PWRINJ-60RGDMG= power injector is powered by a single-phase AC voltage input in the range of 90VAC to 264VAC, providing a maximum output of power at a nominal DC Voltage on the appropriate four data pairs of the output RJ45 connector. The power injector meets the requirements of IEEE 802.3bt as a PSE. It can accept 10/100/1000/2500/5000/10000 Base-T traffic on the input and output RJ45 connectors and pass through these signals between the network and the access point.
Learn More$1,256.25 -
Meraki 802.3at Power over Ethernet Injector - 120 V AC, 230 V AC Input - 1 x Gigabit Ethernet Input Port(s) - 1 x Gigabit Ethernet Output Port(s) - 30 W
Reliable, standard-compliant power for your Meraki devices | Increased Flexibility, Reduced Installation Time and Cost
One of the main limitations in designing your wireless network is the availability of power. Running power cabling is also a primary cost driver of wireless installations. The Meraki PoE injector allows delivery of both data and power to a Meraki access point over a single Ethernet cable, allowing deployment of devices exactly where they are needed to provide the best wireless coverage at a much lower installation cost.
The Meraki 802.3at PoE Injector provides fully compliant 802.3at detection, with disconnect, short-circuit and overload protection to ensure that only 802.3at and 802.3af devices receive power and non-compliant devices are not accidentally damaged. Using this injector, it is possible to power the latest generation of 802.11ac de- vices which require 802.3at power, as well as providing backward compatibility with legacy 802.11n devices with traditional 802.3af power.
Regardless of the deployment scenario, powering Meraki devices with 802.3at Power over Ethernet is a flexible and low-cost method to simplify the installation process while ensuring that network design is not compromised by power availability limitations. Learn More$107.28 -
Meraki MR 802.3at PoE Injector (AU Plug) - 120 V AC, 230 V AC Input - 1 x 10/100/1000Base-T Input Port(s) - 1 x 10/100/1000Base-T Output Port(s) - 30 W - Wall Mountable
Reliable, standard-compliant power for your Meraki devices Increased Flexibility,
Learn More
Reduced Installation Time and Cost
One of the main limitations in designing your wireless network is the availability of power. Running power cabling is also a primary cost driver of wireless installations. The Meraki PoE injector allows delivery of both data and power to a Meraki access point over a single Ethernet cable, allowing deployment of devices exactly where they are needed to provide the best wireless coverage at a much lower installation cost.
The Meraki 802.3at PoE Injector provides fully compliant 802.3at detection, with disconnect, short-circuit and overload protection to ensure that only 802.3at and 802.3af devices receive power and non-compliant devices are not accidentally damaged. Using this injector, it is possible to power the latest generation of 802.11ac devices which require 802.3at power, as well as providing backward compatibility with legacy 802.11n devices with traditional 802.3af power.
Regardless of the deployment scenario, powering Meraki devices with 802.3at Power over Ethernet is a flexible and low-cost method to simplify the installation process while ensuring that network design is not compromised by power availability limitations.$150.71 -
Meraki MR 802.3at PoE Injector (EU Plug) - 120 V AC, 230 V AC Input - 1 x 10/100/1000Base-T Input Port(s) - 1 x 10/100/1000Base-T Output Port(s) - 30 W - Wall Mountable
Reliable, standard-compliant power for your Meraki devices Increased Flexibility,
Learn More
Reduced Installation Time and Cost
One of the main limitations in designing your wireless network is the availability of power. Running power cabling is also a primary cost driver of wireless installations. The Meraki PoE injector allows delivery of both data and power to a Meraki access point over a single Ethernet cable, allowing deployment of devices exactly where they are needed to provide the best wireless coverage at a much lower installation cost.
The Meraki 802.3at PoE Injector provides fully compliant 802.3at detection, with disconnect, short-circuit and overload protection to ensure that only 802.3at and 802.3af devices receive power and non-compliant devices are not accidentally damaged. Using this injector, it is possible to power the latest generation of 802.11ac devices which require 802.3at power, as well as providing backward compatibility with legacy 802.11n devices with traditional 802.3af power.
Regardless of the deployment scenario, powering Meraki devices with 802.3at Power over Ethernet is a flexible and low-cost method to simplify the installation process while ensuring that network design is not compromised by power availability limitations.$150.71 -
Meraki MR 802.3at PoE Injector (UK Plug) - 120 V AC, 230 V AC Input - 1 x 10/100/1000Base-T Input Port(s) - 1 x 10/100/1000Base-T Output Port(s) - 30 W - Wall Mountable
Reliable, standard-compliant power for your Meraki devices
Learn More
Increased Flexibility, Reduced Installation Time and Cost
One of the main limitations in designing your wireless network is the availability of power. Running power cabling is also a primary cost driver of wireless installations. The Meraki PoE injector allows delivery of both data and power to a Meraki access point over a single Ethernet cable, allowing deployment of devices exactly where they are needed to provide the best wireless coverage at a much lower installation cost.
The Meraki 802.3at PoE Injector provides fully compliant 802.3at detection, with disconnect, short-circuit and overload protection to ensure that only 802.3at and 802.3af devices receive power and non-compliant devices are not accidentally damaged. Using this injector, it is possible to power the latest generation of 802.11ac devices which require 802.3at power, as well as providing backward compatibility with legacy 802.11n devices with traditional 802.3af power.
Regardless of the deployment scenario, powering Meraki devices with 802.3at Power over Ethernet is a flexible and low-cost method to simplify the installation process while ensuring that network design is not compromised by power availability limitations.$150.71 -
Meraki Multigigabit 802.3at PoE Injector - 120 V AC, 230 V AC Input - 55 V DC Output - 1 x 10/100/1000Base-T Input Port(s) - 1 x 10/100/1000Base-T Output Port(s) - 30 W
The Cisco Meraki Multigigabit PoE Injector allows delivery of both data and power to a Meraki access point over a single Ethernet cable, allowing deployment of devices exactly where they are needed to provide the best wireless coverage and at much lower installation cost. This PoE injector is specifically designed to meet the power needs of Cisco Meraki 802.3at-compatible multigigabit devices. Check the access point specifications to ensure compatibility.
Learn More$296.59
